Menu
Wheel Fitment Guide & Expertise | Webster Wheels

Wheel Fitment Expertise

Fitment is a set of measurements that must agree with each other and with your vehicle. For more than 25 years we have balanced, installed and removed wheels and tires, and WebsterWheels.com is built around one goal: the right wheel and tire setup for your car, SUV or truck.

Experience you can fit to your vehicle

A spec sheet doesn’t show how a wheel sits behind a brake caliper or how a tire clears a fender. Our team’s years of hands-on work with wheels and tires do. Below are the seven measurements we check on every order, and what each one means for you.

PCD: 5 lugs × 114.3 mm

PCD (bolt pattern)

PCD, or pitch circle diameter, is the diameter of the circle that passes through the center of every lug hole. It is written as lug count × diameter, such as 5×114.3 mm. Your wheel’s PCD must match your vehicle’s hub exactly. A near match, like 5×112 on a 5×114.3 hub, can look right but will not seat safely.

Common patterns: 4×100, 5×114.3, 5×120, 6×139.7. We confirm PCD first, because if it doesn’t match, nothing else matters.

CenterlineOffset (ET), mm

Offset (ET)

Offset is the distance, in millimeters, from the wheel’s centerline to its mounting surface. Positive offset (+) tucks the wheel toward the suspension. Negative offset (−) pushes it outward. It decides how close the wheel and tire sit to the fender, brakes and suspension.

Every vehicle has an acceptable offset range, not a single number. We work within that range so the wheel clears the brakes and stays inside the fender.

Diameter, in inches

Size (diameter)

Wheel size is the diameter measured at the bead seat, in inches, such as 18, 19 or 20. A larger diameter allows a lower-profile tire and a sharper look, but it needs enough brake clearance and a tire that keeps the overall height close to the factory size.

When a customer moves up in size, we pair the new wheel with a tire height that keeps the speedometer and ride accurate.

Width, in inches

Width

Width is measured in inches between the inner faces of the bead seats, such as 8.5 or 9.5. It sets the range of tire widths that can be mounted safely and how far the wheel reaches toward the fender and the inner suspension.

If a customer changes the factory width, we recalculate offset and tire size together so the wheel and tire end up where they should.

Backspacing, in inches

Backspacing

Backspacing is the distance, in inches, from the mounting surface to the rear edge of the wheel. It shows how much room the wheel needs behind it for brakes, suspension and the fender liner. It is tied to width and offset:

Backspacing ≈ (width ÷ 2) + offset in inches. Example: a 9″ wheel with +35 mm offset has about 4.5 + 1.38 = 5.88″ of backspacing. We convert between offset and backspacing for you.

Center bore, in mm

Center bore

Center bore is the diameter of the hole in the middle of the wheel that sits over the vehicle’s hub, in millimeters. It must be equal to or larger than the hub. A bore that is too small will not mount.

If the wheel bore is larger than the hub, hub-centric rings fill the gap so the wheel centers on the hub and runs smooth. We flag this before you order.

245/40R19 245: section width in mm40: sidewall height, % of widthR: radial construction19: wheel diameter in inches

Tire size and recommended tire size

A tire size such as 245/40R19 tells you the tire’s width, sidewall height, construction and the wheel diameter it fits. Every wheel width has a range of tire widths it can safely carry, and the tire’s overall height should stay close to the factory height.

For every wheel we recommend a tire size that fits the wheel width and keeps the overall diameter close to factory, generally within about 3%. Going from an 18″ to a 20″ wheel, for example, means a lower-profile tire.

Changing the factory size or width

Many customers move away from the factory wheel size or width for looks or performance. That works well when the whole setup is adjusted together. We balance each change against:

  • Overall tire height, to protect speedometer accuracy and ride
  • Offset and backspacing, to clear brakes, suspension and fenders
  • Tire width and wheel width, so the tire sits correctly on the rim
  • Your vehicle’s modifications, such as lowering or lift kits, brake upgrades, spacers or air suspension

How we verify your fitment

We combine years of experience with our internal fitment software. The software runs the checks quickly, our team makes the final call, and both get better with every order we review.

  1. You share your vehicle. Year, make, model, trim and any modifications.
  2. We check the fixed specs. PCD and center bore must match, and offset must fall in range.
  3. We confirm size and tires. Wheel diameter and width, plus the recommended tire size.
  4. Our team double-checks. Every order is reviewed again before it ships.

Not sure what fits your vehicle?

Send us your year, make, model and trim, and tell us about any modifications. Our fitment team will point you to the right wheels and tire size.

Monday to Friday, 10 AM to 5 PM.

Fitment guidance is based on the vehicle information you provide. Modifications such as suspension changes, lift or lowering kits, brake upgrades, wheel spacers or air suspension can change what fits, so please tell us before you order. Always test fit the wheels before mounting tires.